UNRESERVED PUBLIC

 

AUCTION

 

SAWMILL & LUMBER REMAN EQUIPMENT

 

Former assets of

 

CHASYN CANADIAN FOREST PRODUCTS LTD.

Auction Date: WEDNESDAY, NOVEMBER 29TH - 10AM
Preview Date: Tuesday, November 28th, Noon - 4pm &
Auction day, 8am - 10am, or by prior appointment
Location:

23347 McKay Avenue, Maple Ridge, BC
(New site of Southcoast Millwork)
One mile west of Albion Ferry

Download auction brochure
Adobe PDF (594 KB)

Download auction catalogue
Adobe PDF (73 KB)


Last Updated: Tuesday, November 28, 2006 - 10:17 PM Pacific Time

PALLET LINE

2000 Baker MultiSelect 3 Head Chop Saw Cut-off System, Model BCO-O, s/n 2K-309; c/w operator’s chair, HPU, Baker BUS-O unscrambler infeed; Infeed belt & roller conveyors; Waste wood conveyors, electrics.

BAKER 3 HEAD CHOP SYSTEM
BAKER 3 HEAD CHOP SYSTEM
BAKER PALLET LINE INFEED
BAKER SYSTEM HYD. UNIT
CLOSE-UP OF 3 HEAD CHOP SAW
CLOSE-UP OF 3 HEAD CHOP SAW
TRIPLE CHOP SAW OPERATOR CONTROLS
RESAWS

(2) 1998 Baker Single Head Horizontal Band Resaws, in tandem, Model BBR-O, controls, etc • Baker 5 Head Horizontal Band Resaw • Belt Conveyor 17” x 25’L; Belt conveyor 45” x 35’L • 8’ Diameter Turntable.

BAKER RESAWS
BAKER RESAWS
BAKER 5 HEAD RESAW
BAKER 5 HEAD RESAW
BAKER 5 HEAD RESAW
BAKER RESAW LINES
BELT CONVEYOR
NOTCHER LINE

Advance 2 Head Pallet Stringer Notcher, c/w hydraulic power unit, unscrambler • Belt Infeed Conveyor, 36” x 45’L.

ADVANCE NOTCHER
ADVANCE NOTCHER UNSCRAMBLER
FINGER JOINT LINE

GreCon Model BF600; FDR-L-205/600; FB600/1200; EKK970-0-0; PASH Konti 9/600; Vickers HPU; Control System w. Siemens Simatic S5; Electrics • 15HP Hydraulic Power Unit.

GRECON FINGER JOINT LINE
GRECON FINGER JOINT LINE
GRECON FINGER JOINT LINE
GRECON FINGER JOINT LINE
GRECON FINGER JOINT LINE
GRECON FINGER JOINT LINE
GRECON FINGER JOINT LINE
GRECON FINGER JOINT LINE
GRECON FINGER JOINT LINE
INDUSTRIAL SINGLE STATION
P.E.T TENONER LINE

Double End Tenoner P.E.T. Saw, (3) heads one side, (2) heads one side; 3 chain infeed deck; Hyd. hoist & (3) roller sections; 3 strand sorting table, 30’L x 8’W; Belt conveyor, 48” x 15’L; waste belt conveyors; Controls & electrics.

TENONER P.E.T. SAW
TENONER P.E.T. SAW
INCLINE BELTS
3 RUN LANDING DECK
P.E.T. LINE PACKAGE DECK
& TILT HOIST
MOULDER & TRIM / SORT LINES

4 Strand Package Infeed Deck, 15’W x 15’L • 4 Arm tilt hoist • 5 Strand Landing Deck, 8’W x 14’L • 9 Strand Transfer to moulder infeed, 4’L x 16’W • Wadkin FD5087 Moulder, s/n 69667; 40HP main drive w/ infeed • Kanag 75HP Frequency Speed Controller • Hyd. power unit • Moulder outfeed belt conveyor, 12” x 10’L • Rollcase transfer to trim saw & sort line, 10 rolls; 5HP • 5 Jump belt suspended incline transfer to trim-sort table • #2 Infeed Line: • 4 Strand Package Infeed Deck, 14’W x 11’L • 4 Arm tilt hoist, 17’W x 48” w/ (4) roller transfers • Stick belt conveyor, 12” x 16’L • (2) Overhead moveable track-mounted trim saws • 4 Strand trim-sort table, 40’L x 13’W; nylon chain • Belt conveyor to turntable • 8’ Diameter turntable • Waste wood conveyor, 20” x 20’ • (2) Hydraulic power units • Hyd. Hoist, 12’ x 4’ c/w (4) roller conveyor sections • 4 Strand outfeed deck • ControlsSCM Superset 23 Molder; 5 heads plus universal; 230 mm wide bed; REF# 031008; 220 volt 3 phase; N.# AB.78840; Motor HP: 1-6 6.6, 13, 13, 13, 8.8, 4.8KW SCM Toolset 16 Grinder, Machine # 5596/98; 400 volt 3 PH 50 Hz.

OVERHEAD TRIM TABLE
OVERHEAD TRIM TABLE
OVERHEAD TRIM TABLE
OVERHEAD TRIM TABLE SYSTEM
5 RUN BELT TRANSFER
LANDING DECK & TRANSFER
PACKAGE DECK & TILT HOIST
TILT HOIST
TRIM TABLE
OUTFEED TRANSFER
TURNTABLE
WADKIN MOULDER
WADKIN MOULDER
MOULDER INFEED
SMC TOOLSET 16 GRINDER
SCM SUPERSET 23
5 HEAD MOULDER
RIP & RESAW AREA

Wadkin Bursgreen Multirip Saw, s/n BSM73302 • Baker Double Head Horizontal Band Resaw, Model BBR-O, s/n 99-2689 • (2) Precision 18M Up-acting Chop Saw, s/n 1848 • 4 Strand chain transfer • Blower Pipe.

WADKIN MULTI-RIP SAW
BAKER 2 HEAD BAND RESAW
BAKER 2 HEAD BAND RESAW
BAKER 2 HEAD BAND RESAW
1 OF 2 PRECISION
CHOP SAWS
2 PRECISION 18M CHOP SAWS
WIDE BELT CONVEYOR
5 HP COMPRESSOR
ELECTRICS & SWITCHGEAR
GRINDING ROOM

Wadkin NV300 Profile Grinder, s/n 98898 • Numerous moulder heads • Hobart 500 amp welder • Double pedestal grinder.

WADKIN NV300
PROFILE GRINDER
PART VIEW OF MOULDER HEADS
HEAD SETUP BENCH
GRINDER, SCALE, ETC.
CUTTERHEAD SET-UP STANDS
ROLLING STOCK & FORKLIFTS

Cat IT-12 Integrated Tool Carrier, s/n X1KF01111X; Diesel; Pneumatic tires; Fully enclosed heated cab; w/forks, bucket & jib boom • Cat V180B 18,000lb Forklift; S/N 17V00537; Diesel; Pneumatic tires; 144"-193" mast; Fully enclosed heated cab • Hyster H120 12,000lb Forklift; LPG; Pneumatic tires; Enclosed cab • Cat V80E 8,000LB Forklift, S/N 37K18611; Diesel; 91-185" mast; S/S; Pneumatic tires; Fully enclosed heated cab • Hyster H80C 8000lb Forklift, LPG • 1999 Cat GP30 6,000LB Forklift, S/N 7AM04730; LPG, Solid pneumatic tires; 87-132" mast; 11443 hrs; Full cab • Nissan 5,000LB Forklift • Clark 4,000lb Forklift, LPG; 2 stage mast; Cushion Tire • Allis Chalmers 40-24 4,000LB Forklift, LPG; Cushion Tire; 2 stage mast • 1994 Nissan FG15 3,000LB Forklift; S/N NJ01-111639; Dual fuel; Pneumatic tires; 77-120" mast.

HYSTER H80C 8000LB FORKLIFT
GENERAL EQUIPMENT

9' turntable w/ Crossman drive, Type HHWV, Size 5, Ratio 120-1, 3HP, 575 V, 1750 RPM, Foot petal, 600 V Plug • Narrobelt 25'' Abrasaplaner Sander,30 HP, 230/460V, 2HP Feed motor, Spare Belts • New Spec Air Dust Collector, 25 bags, 3200 CFM; Factory installed sprinkler system, spare set of bags; 575V 10 HP (Never used)Heian Double End Tennoner, 2-7.5 HP saws, 4-5 HP Stations, 2-7.5 HP [Heads] , With Heads & Saws • Wadkin Bursgreen Jointer, 15.5" cutting surface; Model S400; Ser# 80617; New motor: 5.5HP 208/220V 3 PHCML Multi rip saw, Model SCA-320; S/N 6995, 575V 3 PH (New motor, feed speed control & gear box comboSCMI T130 Shaper, Ser# 080426; 9HP 230V 3 PH; Speeds:3000 to 10,000RPMSCMI T130 Shaper, Ser# 021426; 9HP 230V 3 PH; Speeds:3000 to 10,000RPMUnimac up cut chop saw, Model CS18R; Ser # 33-985; 5HP 220V 3 PHCantek up cut chop saw, Model CS-181; Ser # 129632845; 7HP 220V 3 PH.

200HP BLOWERS
200HP MOTORS
AKEBONO AUTO STRAPPERS
200HP BLOWERS
HITACHI J300 VARIABLE FREQUENCY DRIVES
AUTOMATIC DRILL DRIVE
UNIT BUNKER
24" Abort Gate
SUMNER 48 INCH 16 KNIFE CHIPPER
CAE 6' x 12' CHIP SCREEN
EDGER
TERMS OF SALE
PAYMENT: Full payment - day of sale by Wire Transfer, Cash, Visa, Mastercard or Company Cheque accompanied by bank letter unconditionally guaranteeing payment on presentation. No Personal cheques. Majors - 25% deposit, balance day of sale. Full payment must be made before removal of purchase. There will be a 12% buyer's premium at this sale. For online bidders there is a 15% buyer's premium. All items in auction subject to additions & deletions. REMOVAL: All items must be removed by Friday, December 15, 2006. Everything is sold "as is, where is." All sales final. While quantities and descriptions are believed to be accurate, the auctioneers, owners, employees or counsel make no warranties or guarantees either expressed or implied as to the authenticity, genuineness of, or defects in any lot, and will not be held responsible for any advertising discrepancies or inaccuracies. No warranties whatsoever are made as to condition, merchantability or fitness for any use of any item. Please take advantage of our preview and inspection period. NOTICE TO U.S. BUYERS: 1. Most equipment manufactured in the United States returns duty free. 2. Canadian sales tax is not applicable on goods shipped out of the country. 3. Purchases are payable in Canadian funds. At time of printing the US dollar is worth $1.11 Canadian.
ABSENTEE BIDS
If you are unable to attend this auction, you may register a confidential bid with Tradewest. Tradewest will exercise your bid at the auction, ensuring that you pay only the amount the item sells for, not necessarily the full amount of your bid. Absentee bids are permitted only with pre-registration and receipt by Tradewest of a 25% deposit. Call Tradewest for complete information.
Download Absentee Bid Form
Adobe PDF (50 KB)
CONTACT INFORMATION
For additional information contact Matt Ardiel or Ken Ardiel:
Office: Tel. (604) 530-9351
E-mail: Matt Ardiel
mtardiel@tradewestsales.com

Ken Ardiel
kardiel@tradewestsales.com

 


Back To Top